温度测量范围:

?室内: -10℃～+50℃ (+14℉ ～ +122℉)

?室外: -40℃～+70℃ (-40℉ ～ +158℉)

湿度范围：20%~90%RH

使用电池: 1.5V（AG13）×1个

• 基本功能

温度、湿度显示（可选择室内/室外温度模式）

高、低温度自动报警功能（默认高温28℃，低温18℃）

可设置任意高温、低温报警范围

℃/℉温度切换显示

LED灯指示报警

• 操作方法

1. 按机背指示方向推开电池盖，然后装回电池及电池盖，该机即可使用。
2. 按键功能：

SET设置高、低温度报警范围；

+增加被设项目的数值；

-减少被设项目的数值；

℃/℉切换温度单位以℃(摄氏度)或℉(华氏度)显示；

IN/OUT拨动开关，切换室内/室外温度显示。

1. 在初始状态下按住SET2秒,“SET Hi.高温设置”位置的温度数值（高温度报警数值）开始闪动，按+ /-增加/减少高温度数值，长按加快数值调整；再按SET一次，“SETLo.低温设置”位置的温度数值（低温度报警数值）开始闪动，按+ /-增加/减少低温度数值，长按加快数值调整；后按一次SET键确认设置。
2. 拨动IN/OUT开关到“IN”位置时，显示的是室内温度，此时屏幕上的温度报警范围为室内温度报警范围；反之，拨动IN/OUT开关到“OUT”位置时，显示的是室外温度，此时屏幕上的温度报警范围为室外温度报警范围。
3. 在室内/室外温度间切换时，屏幕上的温度会在10秒内切换到相应的温度显示。
4. 当实际温度超过了设置的温度报警范围时（高于“SET Hi.”位置的温度，或者低于“SETLo.”位置的温度）LED灯会随着闹铃次闪动10秒，与此同时，“SET Hi.”或者 “SETLo.”位置的温度会一直闪动，按任意键可以停止闹铃和LED灯闪动，如果实际温度持续超过温度报警范围，LED灯会随着闹铃每隔一小时闪动一次。

• 注意事项

1. 若该机出现任何不良,请从电池仓中拿掉电池，2秒后再装上.
2. 电池用完后请放回政府指定地点.
3. 如有技术更改恕不另行通知.

1 Specification:

? Temperature Range:

? Indoor: -10℃～+50℃(+14℉ ～+122℉)

? Outdoor: -40℃～+70℃(-40℉ ～+158℉)

? Humidity Range: indoor20%RH ~ 90% RH

? Power-supply: 1.5V (AG13) x 1

2 Functions:

*temperature & humidity display (alternative indoor/outdoor temperature mode)

* Highest/ lowest temperature alarmfunction(default setting: highest 28℃; lowest 18℃)

*Setting the randomtemperature alarm range

* Temperature unit℃/℉changeable

* LED alarm indicator light

3 Operations

3-1 Open battery compartment cover, put on the battery and thecover, then the meter starts to work.

3-2 Button function:

SETset the highest & lowest temperature alarm range.

+increase the value of what is under setting.

- decrease the value of what is under setting.

℃/℉change temperature unit between Celsius (℃) and Fahrenheit (℉).

IN/OUT switch to displayindoor oroutdoortemperature.

3-3 In status of origin, press and hold SET for 2 seconds, the value around “SET Hi.” (The highest temperature alarm value) flashes, press+/ - to increase/decrease the highest temperature alarm value; then pressSET for one time, the value around “SET Lo.” (The lowest temperature alarm value) flashes, press+/ - to increase/decrease the lowest temperature alarm value; finally, pressSET for one time to confirm the setting.

3-4 Turn the IN/OUT switch to “IN”, the meter displays the indoor temperature, and the temperature range on the screen is indoor temperature alarm range; turn the IN/OUT switch to “OUT”, the meter displays the outdoor temperature, and the temperature range on the screen is outdoor temperature alarm range.

3-5 Turnthe switch between IN and OUT, the temperature displayed on screen changes between indoor and outdoor within 10seconds.

3-6 When the temperature is out of the range you set (higher than the temperature you set around “SET Hi.” or lower than the temperature around “SET Lo.”), the alarm will ring with LED light for 10 seconds for the first time, at the same time, the temperature around “SET Hi.” Or “SET Lo.” Which you set flashes, press any button to stop the sound and light; and when the temperature is still goes beyond the range you set, the alarm with light occurs every hour.

4 Attentions:

4-1 Take out the battery from the battery compartment for 2 seconds if any abnormal display appears.

4-2 Put the replaced battery at places appointed bygovernment.

We do not notice if any technical change applied in this meter.