• 产品规格

温度测量范围: -40℃～+120℃(-40℉ ～+248℉)

湿度测量范围: 20%RH～95%RH（当环境湿度低于20%RH时，直接显示Lo；高于95%RH时，直接显示HI）

使用电池: 1.5V（AAA）×1个

• 基本功能

温度，湿度显示

℃/℉温度切换显示

高、低温度自动报警功能（默认高温28℃，低温18℃）

可设置任意高温、低温报警范围

• 操作方法

1. 按机背指示方向推开电池盖，取出电池隔片，然后装回电池盖，该机即可使用。
2. 按键功能：

[SET]设置最高、最低温度报警范围；

[UP(+)]增加被设项目的数值；

[DW(-)]减少被设项目的数值；

1. 在初始状态下按住[SET]2秒, SET Hi.位置的温度数值（最高温度报警数值）开始闪动，按[UP(+)] /[DW(-)]增加/减少最高温度数值；再按[SET]一次，SETLo.位置的温度数值（最低温度报警数值）开始闪动，按[UP(+)] /[DW(-)]增加/减少最低温度数值；最后按一次[SET]键确认设置。

• 注意事项

1. 若该机出现任何不良,请从电池仓中拿掉电池，2秒后再装上.
2. 电池用完后请放回政府指定地点.
3. 如有技术更改恕不另行通知.

1 Specification:

?? Temperature Range: -40℃～+120℃(-40℉ ～+248℉)

?? Humidity Range: indoor20% ~ 95% RH（When the humidity ＜20%RH, display “Lo” directly;When the humidity＞95%RH, display “HI” directly）

?? Power-supply: 1.5V (AAA size) x 1

2 Functions: 

* Temperature& humidity display

* Temperature unit℃/℉changeable

* Highest/ lowest temperature alarmfunction(Default setting: highest 28℃; lowest 18℃)

* Adjustable temperature alarm range

3 Operations

3-1Open battery compartment cover, take out the polarity insulator, put on the cover, then the meter starts to work.

3-2 BUTTON function:

[SET] set the highest & lowest temperature alarm range.

[UP(+)]increase the value of what is under setting.

[DW(-)] decrease the value of what is under setting.

3-3In status of original, press and hold [SET] for 2 seconds, the value around “SET Hi.” (The highest temperature alarm value) flashes, press[UP(+)]/[DW(-)] to increase/decrease the highest temperature alarm value; then press[SET] for one time, the value around “SET Lo.” (The lowest temperature alarm value) flashes, press[UP(+)]/[DW(-)] to increase/decrease the lowest temperature alarm value; finally, press[SET] for one time to confirm the setting.

4  Attentions:

4-1 Take out the battery from the battery compartment for 2 seconds if any abnormal display appears.

4-2 Put the replaced battery at places appointed bygovernment.

4-3 We do not notice if any technical change is applied in this meter.

1 Specification:

?? Temperature Range: -40℃～+120℃(-40℉ ～+248℉)

?? Humidity Range: indoor20% ~ 95% RH（When the humidity ＜20%RH, display “Lo” directly;When the humidity＞95%RH, display “HI” directly）

?? Power-supply: 1.5V (AAA size) x 1

2 Functions: 

* Temperature& humidity display

* Temperature unit℃/℉changeable

* Highest/ lowest temperature alarmfunction(Default setting: highest 28℃; lowest 18℃)

* Adjustable temperature alarm range

3 Operations

3-1Open battery compartment cover, take out the polarity insulator, put on the cover, then the meter starts to work.

3-2 BUTTON function:

[SET] set the highest & lowest temperature alarm range.

[UP(+)]increase the value of what is under setting.

[DW(-)] decrease the value of what is under setting.

3-3In status of original, press and hold [SET] for 2 seconds, the value around “SET Hi.” (The highest temperature alarm value) flashes, press[UP(+)]/[DW(-)] to increase/decrease the highest temperature alarm value; then press[SET] for one time, the value around “SET Lo.” (The lowest temperature alarm value) flashes, press[UP(+)]/[DW(-)